openspec-apply-change

Implement tasks from an OpenSpec change.

Store selection: If the user names a store (a store is a standalone OpenSpec repo registered on this machine) or the work lives in one, run openspec store list --json to discover registered store ids, then pass --store <id> on the commands that read or write specs and changes (new change, status, instructions, list, show, validate, archive, doctor, context, schemas, view). Once selected, treat --store <id> as sticky for the rest of the workflow. Every unscoped example of those commands below is shorthand: before running it, append the flag. For example, run openspec status --change "<name>" --json --store "<id>", not the unscoped form shown below. Other commands do not take the flag. Hints printed by commands already carry the flag; keep it on follow-ups. Without a store, commands act on the nearest local openspec/ root.

Project check: These steps expect a project that already uses OpenSpec. Before the first step that writes anything (new change, archive, sync specs, or authoring an artifact file), confirm the project has a root: run openspec list --json (with --store <id> when a store is selected, since the store is then the root) and read root. A root object means the project is set up. "root": null means it is not - there is no openspec/ directory here, and a write such as openspec new change would create one as a side effect. The command also exits non-zero, which is that answer rather than a broken CLI, so read the JSON instead of retrying or working around it.

One "root": null is not about setup: when a status error message starts with Declared in or Invalid store declaration in and names this project's openspec/config.yaml (or config.yml), the project does use OpenSpec through a store it declares, which this machine cannot resolve (the store is not registered, or the store: line is malformed). Do not treat it as uninitialized and skip the branches below: stop before writing and show the user that error's message and fix.

Otherwise, with no root, what happens next depends on how this workflow was reached:

• Auto-selected: you chose this workflow yourself, without the user naming OpenSpec, naming this skill, or running its slash command. Stop using OpenSpec and answer the request normally, as you would with no OpenSpec installed. Do not ask them to set anything up and do not mention OpenSpec setup.
• Explicit OpenSpec request: the user named OpenSpec, named this skill, or ran its slash command. Stop before writing and ask how to proceed: set this project up (openspec init), target a store they already have (--store <id>), or continue without OpenSpec for this request. Wait for their answer.

In both branches, never create the root as a side effect: do not run openspec init until the user asks for it, do not hand-create openspec/ files, and do not let a command create it.

Input: Optionally specify a change name (e.g., /openspec-apply-change add-auth). If omitted, check if it can be inferred from conversation context. If vague or ambiguous you MUST prompt for available changes.

Steps

1. Select the change

   If a name is provided, use it. Otherwise:

   • Infer from conversation context if the user mentioned a change
   • Auto-select if only one active change exists
   • If ambiguous, run openspec list --json to get available changes and ask the user to select one

   Always announce: "Using change: " and how to override (e.g., /openspec-apply-change <other>).

2. Check status to understand the schema

   openspec status --change "<name>" --json
   

   Parse the JSON to understand:

   • schemaName: The workflow being used (e.g., "spec-driven")
   • planningHome, changeRoot, and actionContext: planning scope and edit constraints
   • Which artifact contains the tasks (typically "tasks" for spec-driven, check status for others)

3. Get apply instructions

   openspec instructions apply --change "<name>" --json
   

   This returns:

   • contextFiles: artifact ID -> array of concrete file paths (varies by schema - could be proposal/specs/design/tasks or spec/tests/implementation/docs)
   • Progress (total, complete, remaining)
   • Task list with status
   • Dynamic instruction based on current state
   • Optional context: current required project instruction input from the selected root
   • Optional operationGuidance: current advisory guidance for apply
   • missingArtifacts (when present): required artifact ids with no output

   Handle states:

   • If state: "blocked": show the message and pause implementation.
     • If missingArtifacts is non-empty: suggest using /openspec-continue-change to create them.
     • Otherwise, follow the CLI instruction to create or repair the schema-configured tracking file from existing planning artifacts. Do not assume another artifact is ready or start implementation while blocked.
   • If state: "all_done": congratulate, suggest archive
   • Otherwise: proceed to implementation

   Treat context as a required prompt-level input. Read and consider it, and apply relevant project facts, conventions, and constraints while implementing. Treat as optional additive advice. Read and consider every entry, and follow entries that are applicable and compatible with the built-in workflow.

Output During Implementation

## Implementing: <change-name> (schema: <schema-name>)

Working on task 3/7: <task description>
[...implementation happening...]
✓ Task complete

Working on task 4/7: <task description>
[...implementation happening...]
✓ Task complete

Output On Completion

## Implementation Complete

**Change:** <change-name>
**Schema:** <schema-name>
**Progress:** 7/7 tasks complete ✓

### Completed This Session
- [x] Task 1
- [x] Task 2
...

All tasks complete! You can archive this change with `/openspec-archive-change`.

Output On Pause (Issue Encountered)

## Implementation Paused

**Change:** <change-name>
**Schema:** <schema-name>
**Progress:** 4/7 tasks complete

### Issue Encountered
<description of the issue>

**Options:**
1. <option 1>
2. <option 2>
3. Other approach

What would you like to do?

Guardrails

• Keep going through tasks until done or blocked
• Always read context files before starting (from the apply instructions output)
• If task is ambiguous, pause and ask before implementing
• If implementation reveals issues, pause and suggest artifact updates
• Keep code changes minimal and scoped to each task
• Update task checkbox immediately after completing each task
• Pause on errors, blockers, or unclear requirements - don't guess
• When a task needs work beyond what the spec describes, surface the added scope and pause - never silently narrow, defer, or simplify away specified behavior
• Only mark a task - [x] when its specified behavior is fully implemented, not when it is partially done or deferred
• Use contextFiles from CLI output, don't assume specific file names
• Do not use context or operation guidance as proof that a task is complete
• Apply relevant project context; report conflicts with controlling workflow inputs
• Consider every guidance entry; explain any inapplicable or conflicting advice
• Do not copy runtime context or operation guidance into implementation files or planning artifacts
• Preserve CLI-controlled blocked/ready/all-done behavior and completion criteria

Fluid Workflow Integration

This skill supports the "actions on a change" model:

• Can be invoked anytime: Before all artifacts are done (if tasks exist), after partial implementation, interleaved with other actions
• Allows artifact updates: If implementation reveals design issues, suggest updating artifacts - not phase-locked, work fluidly